Stainless Steel Shape

High precision with minimal material waste.
Clean cuts with smooth edges, reducing the need for additional finishing.
Suitable for complex shapes and intricate designs.
Can handle a variety of thicknesses and materials.
Cutting Size Range:
Length: 100 mm to 12,000 mm
Width: 100 mm to 3,000 mm
Height: Flat sheets, typically not suitable for 3D objects
Thickness: 0.5 mm to 30 mm (depending on material)
Seam Width: 0.1 mm to 0.4 mm
High Tolerance: ± 0.1 mm
Additional Notable Limits: Laser beam width is typically less than 1 mm, allowing for intricate designs.

Fast cutting speeds, especially for thicker materials.
Can cut electrically conductive metals.
More cost-effective for thicker steel compared to laser cutting.
Versatile in cutting different shapes and contours.
Cutting Size Range:
Length: 50 mm to 6,000 mm
Width: 50 mm to 3,000 mm
Height: Flat sheets and some 3D shapes, limited complexity
Thickness: 1 mm to 50 mm (can go up to 150 mm for specialized plasma systems)
Seam Width: 1.5 mm to 3 mm
High Tolerance: ± 0.5 mm
Piercing Capacity: Plasma can pierce materials up to 40 mm thick without pre-drilling.

No heat-affected zones, maintaining material integrity.
Can cut virtually any material, including thick metals.
High precision and ability to cut complex shapes.
Environmentally friendly, using water and abrasives.
Cutting Size Range:
Length: 100 mm to 7,000 mm
Width: 100 mm to 4,000 mm
Height: Suitable for both flat and contoured objects
Thickness: 1 mm to 150 mm (up to 200 mm for softer materials)
Seam Width: 0.8 mm to 1.2 mm
High Tolerance: ± 0.1 mm to ± 0.2 mm
Additional Notable Limits: Cutting angle tolerance is typically ± 1 degree for very thick materials.

Cost-effective for thick steel sections.
Can cut through very thick materials.
No requirement for electricity, making it suitable for remote sites.
Reliable and simple to use for basic cuts.
Cutting Size Range:
Length: 500 mm to 20,000 mm
Width: 500 mm to 5,000 mm
Height: Primarily for flat, thick plates
Thickness: 6 mm to 300 mm
Seam Width: 2 mm to 6 mm
High Tolerance: ± 1 mm
Heat-Affected Zone: Flame cutting results in a heat-affected zone (HAZ) ranging from 1 mm to 5 mm from the edge of the cut, which may need further processing for certain applications.

High-speed cutting, ideal for mass production.
Very clean cuts with minimal waste.
Excellent for cutting thin steel sheets and coils.
Minimal material distortion.
Cutting Size Range:
Length: 100 mm to 6,000 mm (depending on coil size)
Width: 20 mm to 2,000 mm (slitting width can be as narrow as 20 mm)
Height: Limited to flat sheets
Thickness: 0.5 mm to 15 mm
Seam Width: 0.1 mm to 0.5 mm (for slitting)
High Tolerance: ± 0.2 mm
Slit Edge Burr: Can range from 0.1 mm to 0.5 mm, depending on material and cutting method.

Non-contact cutting method, no heat-affected zones.
Excellent for cutting thin and delicate parts.
No tool wear, leading to consistent quality.
Ideal for hard metals and alloys.
Cutting Size Range:
Length: 10 mm to 1,000 mm (for small, precision parts)
Width: 10 mm to 500 mm
Height: Limited to thin, flat parts or small, precise cuts
Thickness: 0.1 mm to 10 mm
Seam Width: Less than 1 mm
High Tolerance: ± 0.05 mm
Edge Roughness: Electrochemical cutting results in edge roughness of less than 10 microns, making it ideal for delicate and precision applications.