Application of high temperature alloy in aerospace industry
Superalloys can be divided into three groups according to their matrix structure: iron-based nickel-based and chromium-based.
According to the mode of production, it can be divided into deformation superalloy and cast superalloy. It is an indispensable raw material in the aerospace field. It is a key material for the high-temperature parts of aerospace and aeronautical engines. Mainly used for manufacturing combustion chamber, Turbine Blades, guide blades, compressor and turbine disk, turbine casing and other parts. The working temperature ranges from 600 ° C to 1200 ° c. the mechanical and environmental conditions vary with the parts in use. The mechanical, physical and chemical properties of the alloy are strictly required, which is the performance of the engine, the decisive factor of reliability and life. Therefore, superalloy is one of the key research projects in the field of aerospace and national defense in developed countries.

High-Temperature Alloy Applications
1. High-Temperature Alloys for Combustion Chambers
The combustion chamber of an aero-engine turbine (also known as the flame tube) is one of the key high-temperature components. Due to processes such as fuel atomization and oil-gas mixing occurring in the combustion chamber, temperatures can reach as high as 1500°C to 2000°C, with wall temperatures reaching 1100°C. Additionally, the chamber must withstand thermal and gas stresses. High thrust-to-weight ratio engines often use annular combustion chambers, which are shorter and have higher thermal intensity; within these chambers, temperatures can reach 2000°C, with wall temperatures of 1150°C after film cooling or vapor evaporation cooling. The significant temperature gradients between different areas create thermal stresses, resulting in distortions, cracks, and other failures due to thermal shock and thermal fatigue loads. Typically, combustion chambers are made from plate alloys, and the technical requirements for specific components include: resistance to oxidation and gas corrosion under high-temperature conditions; sufficient transient and long-term strength, thermal fatigue performance, and low expansion coefficients; adequate plasticity and weldability to ensure processability and connections; and good microstructural stability under thermal cycling to guarantee reliable operation over their lifespan.
1)MA956 Alloy Porous Layer Plates
Early porous layer plates were made from thin HS-188 alloy sheets, processed through photography, corrosion etching, and perforation, followed by diffusion bonding. The internal layers can be designed to create ideal cooling channels. This structure allows for a reduction in cooling gas requirements to 30% of that needed for traditional film cooling, enhancing engine thermal cycle efficiency and reducing the actual heat load on combustion chamber materials, thus lightening weight and increasing thrust-to-weight ratio. Currently, technological breakthroughs are still needed for practical use. The MA956 porous layer plate, a new generation of combustion chamber material from the U.S., can be used at temperatures of 1300°C.
2)Ceramic Matrix Composites in Combustion Chambers
The U.S. began testing the feasibility of ceramics for gas turbines in 1971. By 1983, various groups engaged in advanced materials development had established performance metrics for gas turbines used in advanced aircraft, including raising turbine inlet temperatures to 2200°C, operating under chemically calculated combustion conditions, reducing component density from 8 g/cm³ to 5 g/cm³, and eliminating cooling for these components. The materials studied included not only single-phase ceramics but also graphite, metal matrix, and ceramic matrix composites, as well as intermetallic compounds. Ceramic matrix composites (CMCs) offer several advantages: their thermal expansion coefficients are much lower than those of nickel-based alloys, and coatings tend to peel easily. Creating CMCs with intermediate metal mats can overcome peeling issues and represents a direction for the development of combustion chamber materials. Such materials can operate with only 10% to 20% cooling air, resulting in metal back temperatures around 800°C, significantly lower than those from divergent cooling and film cooling. The V2500 engine uses cast high-temperature alloy B1900 with ceramic-coated protective tiles, and the direction of development is to replace B1900 (with ceramic coating) tiles with SiC-based composites or oxidation-resistant C/C composites. CMCs are the materials for combustion chambers in engines with thrust-to-weight ratios of 15 to 20, operating at temperatures of 1538°C to 1650°C, used for flame tubes, floating wall panels, and afterburner combustion chambers.
2.High-Temperature Alloys for Turbine Sections
Aero-engine turbine blades are among the components that experience the most severe temperature loads and harsh operating environments. They must withstand significant and complex stresses at high temperatures, leading to very stringent material requirements. High-temperature alloys for turbine blades can be classified as follows:
1)High-Temperature Alloys for Stators
Stators are among the components in a turbine engine that experience the most thermal shock. When uneven combustion occurs in the combustion chamber, the first-stage stator blades endure substantial thermal loads, which are a primary cause of stator failure. Their operating temperatures are typically about 100°C higher than those of turbine blades, but they are static components and experience less mechanical load. However, they are susceptible to thermal stresses that can lead to distortion, thermal fatigue cracks, and localized burning. The alloys used for stator blades should possess the following characteristics: sufficient high-temperature strength, durability against creep, good thermal fatigue performance, high oxidation and thermal corrosion resistance, resistance to thermal stresses and vibrations, bending deformation capabilities, good castability, and coating protection performance.
Currently, advanced high-thrust engines often use hollow cast blades made from directional or single crystal nickel-based high-temperature alloys. High-thrust engines operate at temperatures reaching 1650°C to 1930°C, necessitating the use of thermal barrier coatings. Under cooling and coating protection conditions, the operating temperature of blade alloys exceeds 1100°C, imposing new and higher demands for temperature, density, and cost on future stator blade materials.
2)High-Temperature Alloys for Turbine Working Blades
Turbine blades are critical rotating components in aero-engines, with operating temperatures that are 50°C to 100°C lower than those of stator blades. During rotation, they experience significant centrifugal stress, vibrational stress, thermal stress, and airflow erosion, operating under harsh conditions. High-thrust engines require that the lifespan of thermal end components exceeds 2000 hours. Therefore, turbine blade alloys must exhibit high creep resistance and long-term fracture strength at operating temperatures, excellent high- and medium-temperature performance, including high and low cycle fatigue, thermal fatigue, sufficient plasticity, and impact toughness, as well as high oxidation and corrosion resistance. They should have good thermal conductivity and as low a linear expansion coefficient as possible, good castability, and long-term microstructural stability with no TCP phase precipitation at operating temperatures. The alloys used have evolved through four stages: wrought alloys such as GH4033, GH4143, and GH4118; cast alloys such as K403, K417, K418, and K405; directional solidification alloys like DZ4 and DZ22; and single crystal alloys such as DD3, DD8, and PW1484. Development has now reached the third generation of single crystal alloys. In China, single crystal alloys DD3 and DD8 are used in turbine, turbofan engines, helicopters, and naval engines.
3)High-Temperature Alloys for Turbine Discs
The turbine disc is the rotating load-bearing component that experiences the highest stress in turbine engines. For engines with thrust-to-weight ratios of 8 and 10, the rim temperature reaches 650°C and 750°C, while the hub temperature is about 300°C, resulting in significant temperature differences. During normal rotation, the disc drives the blades at high speeds, enduring maximum centrifugal, thermal, and vibrational stresses. Each start and shutdown represents a cycle, with the hub, throat, groove bottom, and rim all experiencing different composite stresses. The alloys used must exhibit the highest yield strength, impact toughness, and no notch sensitivity at operating temperatures, low linear expansion coefficients, certain oxidation and corrosion resistance, and good machinability.
4)High-Temperature Alloys for Aerospace Applications
In liquid rocket engines, high-temperature alloys are used for combustion chamber injector panels, turbine pump bends, flanges, graphite fin fasteners, and more. In the thrust chamber, high-temperature alloys serve as the fuel injector panel, with turbine pump bends, flanges, and graphite fin fasteners also made from these materials. China's YF73 and YF75 engines utilize GH3030 alloy wire woven into a mesh, which is then rolled and sintered into porous, divergent cooling panels for combustion chamber injectors. Turbine rotors began using GH1040 and GH2038A, later transitioning to GH4169 through integral forging, with the disc machined and blades electrolytically processed to overcome excessive deformation issues during prolonged testing with GH1040. Comparison of the performance of GH1040 and GH4169 shows that the material requirements for turbine rotors in long-range missile engines adhere to standards of 800°C at 398 MPa for 20 minutes; GH4169 can achieve stable microstructural performance for 30 minutes, while GH1040 can only maintain 294 MPa for 6 minutes at 800°C, failing to meet operational requirements. Notably, from -253°C to room temperature, the strength of GH4169 increases by 392 MPa to 400 MPa, with minimal change in plasticity and good low-temperature impact toughness. Therefore, GH4169 is utilized for critical load-bearing components like turbine rotors, shafts, and fasteners.
In U.S. liquid rocket engines, turbine rotor materials include the intake manifold, turbine blades, and discs. China primarily employs GH1131 alloys for turbine blades, varying with operating temperature, sequentially adopting Inconel x, Alloy 713C, Astroloy, and Mar-M246; disc materials include Inconel 718 and Waspaloy, with China predominantly using GH4169 and GH4141 for integral turbines and GH2038A for engine shafts.
